Set inspection criteria for a bulk phone case order by turning each approved order requirement into a check anyone can observe. Then classify each possible failure by its consequence, and agree on who inspects, when, and who decides what happens to a failed unit.
Phone case manufacturers and buyers should settle all of this in writing before production starts. The order’s own specification, artwork, and approved samples supply the values. A generic checklist cannot.
Build the criteria from the approved order
Start with documents both sides have approved rather than a generic checklist. For a case order, ASQ’s quality-planning guidance shows how to translate order requirements into defined actions by specifying what is needed, who will do it, and how.
Trace each check to a controlled reference
Each criterion needs a source. Identify the order requirement and the approved specification, drawing, artwork file, or physical sample that defines it. Record the reference name and its version, so the buyer and the phone case factory compare units against the same thing. If a revised artwork file replaced an earlier one, the agreement should name the revision in force. Leave out requirements that don’t apply to this particular case. An extra check with no matching requirement only creates arguments later.
Write the acceptance check in observable terms
A useful check says what the inspector will look at or measure, the method and conditions, and the acceptance rule or where that rule comes from. Say the order specifies artwork placement. The row should point to the approved artwork or sample and state how placement will be compared against it. If no tolerance has been agreed, the row stays open until both parties set one. Do not guess a number. A row with a blank acceptance rule is not a finished criterion.

One working matrix keeps these rows in one place. Use one row per applicable requirement:
| Agreement field | What the parties record |
|---|---|
| Requirement and reference | Order line, document or sample, version |
| Observable characteristic | What is seen or measured |
| Method and conditions | How and under what conditions it is checked |
| Acceptance rule | Agreed rule or its controlled source |
| Stage and sampling basis | When it is checked; plan if sampled |
| Checker and verifier | Named roles |
| Recorded result | Finding and supporting evidence |
| Defect category | Order-defined, consequence-based |
| Disposition and authority | Allowed responses; who decides |
Define defect categories by consequence
Classify failures by their practical consequence for this specific order rather than relying on ungrounded category labels alone. As ASQ’s defect-classification guidance highlights, defect categories rank seriousness and require definitions tailored to the product being sampled.
Define seriousness for this order
Ask what actually happens if a given check fails. Does the failure affect how the case functions for the end user, how it represents your brand, or only its appearance in a way the order tolerates? Write the answer down as the category’s definition. Labels such as critical, major, and minor are common, but they don’t apply automatically. Two buyers can use the same label for very different failures. What matters is that your definitions are written down and both sides accept them.
Pair each category with a response and decision owner
A category is only actionable when it tells people what to do next. For each order-defined category, record:
-
Consequence: the failure effect that places a defect in this category
-
Notification and escalation: who must be told, and how fast the issue moves up
-
Disposition options: terms to negotiate, such as holding units aside pending a decision, rework and reinspection, replacement, rejection, or a documented deviation
-
Decision authority: the named person who can approve the disposition or release
These dispositions are options for the parties to agree on. No source makes any of them mandatory.
Agree who inspects, when, and how results are decided
Name the roles, stages, records, and decision rights for every check before production starts. ASQ’s quality-plan elements outline inspection at appropriate stages, named responsibilities, work verification, documented performance, and corrective action owners, while your specific purchase order sets the actual milestones.
Assign inspection stages, checkers, and records
For each agreed inspection stage, write down:
-
The checker who performs the check, and the verifier who confirms it
-
The production stage at which it happens
-
The result and evidence recorded, such as notes or photos
-
Who reviews the record
-
Who receives notice when a check fails
-
Who owns follow-up and corrective action
Also state what happens if the buyer and supplier disagree about a finding. That is the gap most likely to stall a shipment.
Choose a method and sampling basis only when applicable
Tie each check’s method and conditions to the approved requirement or an explicit buyer-supplier agreement. If you choose sampling, write down the actual plan. ASQ’s explanation of sampling plans notes that acceptance sampling plans state the sample sizes and the acceptance or non-acceptance criteria. It also explains a key difference. Attribute checks record whether a characteristic is present or absent, while variable checks use measured values such as length. Define the lot, the sample size, and the accept or reject rule. Never assume a default.
Approve the inspection agreement before production
The criteria are ready only when nothing is left open. Use this go/no-go gate:

-
Every check has an agreed method and an acceptance rule or controlled source. Any blank row means no-go.
-
Conflicting references, such as two artwork versions, are resolved to one.
-
Each defect category has a defined response and a named decision-maker.
-
Release authority is explicit.
-
Both parties sign the same controlled version before production begins.
Once signed, inspection records become the objective evidence and traceability both sides rely on. If you are preparing an order with us, our team can work through this agreement with you through our official store.
FAQs
Who should hold the master copy of the inspection agreement?
Pick one controlled copy and name its owner, usually whoever manages the order on the buyer side. Any change should get a new version number and approval from both parties. That way, inspectors never work from an outdated file.
What if the specification changes after production starts?
Treat it as a new revision. Update the affected rows, resolve their acceptance rules, and re-approve before inspecting against the new version. Units made under the old version should be judged against the version in force when they were produced, unless both parties agree otherwise.
Can a third-party inspector replace the supplier’s own checks?
A third party can fill the checker or verifier role if the agreement names them. It does not remove the need for defined criteria. An outside inspector still needs the same references, methods, and acceptance rules, and someone still needs authority to decide disposition.
Do criteria from a previous order carry over to a repeat order?
Only after you confirm the references still match. If the artwork, case model, or specification changed, review those rows first. Reusing a matrix without checking versions can apply the wrong rule.
Next step: price your order
Send your device list, target quantity, and any print or material requirements to our team. We will reply with tooling cost, MOQ, sampling time, and lead time for your exact build. Request a quote