To specify phone case openings, tie every camera, button, port, and speaker requirement to one named handset. Don’t rely on a phone family name or a reference photo. For each feature, record where it sits on that device, what opening or covered treatment you want, which drawing or physical measurement sets the clearance, and what the user must still be able to do.
Then check a supplier sample on that same handset and record each result as a pass or a fail. Fix any mismatch before you approve the sample. The sections below cover each step in that order.
Identify the exact target handset and reference
Start by recording the full marketed model and generation, such as the brand, product line, and model name. Add the model or regional version when it changes the layout. “Brand X phone” or a broad family name is not a spec. Phones in the same family can put cameras, controls, and ports in different places, and a supplier will fill any gap with a guess.
Write the device identity and the fit reference into the specification itself. A good reference is either the manufacturer’s documentation for that exact device or the physical handset you will use to test samples. Use the same reference from drawing review through sample approval. A reference photo can help with appearance, but it is not dimensional evidence. Photos don’t show depth, and lens distortion can shift where features appear to sit. Before you approve any dimensions, confirm them against the actual handset.
For iPhone targets, Apple gives an on-device way to find the exact identity. Apple’s model-number instructions say to open Settings, tap General, tap About, and then tap the part number shown next to Model Number to display the model number. Record that number in your brief. This route is specific to iPhone. Other manufacturers have their own ways to identify a device, so use the method each one documents.
Translate each opening and control into a testable requirement
Each feature needs four pieces of information: its location, its treatment, its clearance reference, and its required function. Location alone tells the supplier where to cut. It doesn’t tell them what the finished case must let the user do. Describe locations from one named orientation and use it throughout the spec, for example “screen facing you, port at the bottom.”
| Feature | Location and orientation reference | Treatment and clearance reference | Required access or function |
|---|---|---|---|
| Camera | Back panel area, by edge and corner | Open cutout; clearance per approved drawing or handset check | Clear lenses and flash; normal camera use |
| Buttons and controls | Each control by edge and position | Open cutout or covered control; reference drawing | Stated press or switch action works |
| Port | Edge and position along it | Opening per drawing or handset check | Named cable or accessory connects |
| Speakers | Grille(s) by edge and position | Opening per drawing or handset check | Speaker output stays available |
Leave every number in the table blank until a verified handset or an approved device-specific drawing supports it. A blank field shows that the work is still open. A guessed number looks settled when it isn’t.
Camera opening
Describe the camera area by its position on the back panel relative to the handset edges, in your named orientation. List each element that must stay clear: every rear lens, the flash, and any other camera feature the handset has. Take the shape and clearance of the opening from the approved drawing or from measurements of the physical handset, not from an estimate. State the intended use too, for example: “rear cameras and flash must work without the case blocking the view.” That sentence gives the sample check something concrete to verify.

Buttons and controls
List only the controls the target handset actually has. Identify each one by edge, position, and required action. Control sets can change between generations of the same family. Apple’s iPhone control guide shows this: it lists an Action button on iPhone 17e, iPhone 16e, and iPhone 15 Pro models, a Ring/Silent switch on other model groups, and Camera Control on supported models. A spec copied from an older model could leave a cutout where the new device needs a button, or the other way around. This example shows that layouts vary. It does not make any claim about case fit.
For each control, choose an open cutout or a covered treatment. The choice changes what you need to write. An open cutout needs location and clearance so the user can reach the control directly. A covered control also needs the intended operation spelled out: which button the cover presses, and that it must press only that button. A switch, such as Apple’s Ring/Silent switch, generally needs an opening wide enough to move it through its full travel.
Port opening
Identify the port by its edge and position in your named orientation. Then name the cable or accessory that must fit, such as the handset’s own charging cable or a specific accessory your customers use. Connector housings differ in size, so “port access” means little until you name the plug. Set the opening size and any clearance from the approved drawing or the physical handset. Don’t assume one universal size works for every device.
Speaker openings
Identify the speaker grille or grilles by edge and position. State that the case must leave the intended speaker output available. If your team has agreed on a measured acoustic test and limit for this device, include it. If not, don’t invent one. Name the visual and listening check you’ll use on the sample so the result can be compared from one sample round to the next.
Check the supplier sample against the handset
Test the sample on the same named handset the specification describes, and check every requirement in the table. Something that looks right in a photo can still block a lens or bind on a cable. Treat an unclear result as unresolved, not as a pass.
Confirm fit and camera access
Put the sample on the target handset and confirm it sits as intended, with no lifting at the corners or edges. Open the camera and check the preview for any visible edge of the case in the frame. Then use each camera function that handset has, including the flash. Record the result for each requirement. Don’t compare the sample with a different phone or a product image, because that only tells you how it fits that phone or that image.
Operate every specified control
Press or switch each listed control with the case on and confirm the handset responds as expected. For covered controls, check that the stated action happens with normal pressure. Record it as a mismatch if a press fails, needs too much force, or triggers the neighboring button. Apple’s handling guidance also warns against applying excessive pressure to a button, so a cover that only works under heavy pressure fails.
Check port and speaker access
Plug in the named cable or accessory with the case on. It should line up and seat fully without force. Apple’s connector guidance for iPhone says never to force a connector into a port. If the connector and port don’t join with reasonable ease, check for obstructions and make sure the connector matches the port and is positioned correctly. If the case edge is what stops the plug, record a port opening mismatch. Don’t push harder.
For speakers, check whether the case visibly covers any grille. Then play the same audio clip at the same volume with the case off and with it on, and note any change you can hear. Unless you agreed on a measured limit earlier, record these as observations.
Record results before approval
For each requirement, log the feature, the reference used, the result (pass or fail), and a short note on what you saw. Send failed or unclear items back to the supplier with that record. Decide whether the sample or the spec needs to change, since sometimes a spec error causes the failure. After any revision, repeat the affected checks on the same handset. Approve only when every requirement has a recorded pass.

When we work with a buyer’s brief, a record set up this way lets both teams talk about the same feature, reference, and result.
FAQs
Can I specify phone case openings from a product photo?
No. A photo can show style, but it doesn’t confirm dimensions or position. Base the spec on device-specific documentation or the physical handset, and confirm it on a sample.
Do I need to list exact cutout dimensions in the brief?
Only when an approved drawing or a measured handset supports them. Otherwise, name the reference that will set the clearance and leave the value blank until it is checked.
When does a covered button need extra detail?
Always. A cover changes how the control works, so state which control it presses, that it must not trigger nearby buttons, and that it should work with normal pressure.
What if the charging cable doesn’t fit the sample’s port opening?
Don’t force it. Apple advises iPhone users to check for obstruction and alignment when a connector doesn’t join easily. If the case blocks the plug, record a failure and revise the opening.
Should I retest everything after a supplier revision?
Retest every feature the change could affect, on the same handset. Re-seating the whole case is a quick way to catch side effects.